aroundgogl.blogg.se

Ultimaker cura connect to printer
Ultimaker cura connect to printer













  1. #Ultimaker cura connect to printer install#
  2. #Ultimaker cura connect to printer update#
  3. #Ultimaker cura connect to printer upgrade#
  4. #Ultimaker cura connect to printer software#
  5. #Ultimaker cura connect to printer plus#

Notifications alert users whenever a printer needs attention. Cura Connect's networking capabilities allow users to select and group printers, queue jobs, monitor prints, and strategically schedule maintenance operations. Imagine if an institution buying a bank of 200 3D printers had to ALSO hire a squad of highly trained 3D printer operators and maintainers? What if you could tell them you need, say, only a single person to run the fleet? That’s what Ultimaker is working towards here, I believe.Cura Connect is especially useful for organizations that use the Ultimaker 3 for prototyping and small-scale production and need an overview of pending print jobs in one intuitive interface. This could provide a huge boost to Ultimaker’s sales, as they could now approach large institutions with an effective solution that might have otherwise been difficult for buyers to accept.

#Ultimaker cura connect to printer install#

There is some way that the machines will be maintained, perhaps like automobiles when they notify you that it’s time for serviceĪll this is very good, and apparently it will be automatically set up once you install a set of Ultimaker 3’s with Cura Connect and launch Cura (version 3.0, presumably).Job dispatching will be intelligent and perhaps automatically route jobs to available machines with the correct material loaded.There will be a way to monitor print operations in a centralized, remote manner.Their writeup is frustratingly brief, so we cannot know yet exactly what it will do, but reading between the lines I can gather the following: Now it seems that Ultimaker may be launching their version with Cura Connect. Since then some other companies desired to get that same type of business. Bulk sales are great for any company, especially 3D printer companies. It’s been installed in a few educational institutions, but the big deal for MakerBot was that it enabled them to sell large quantities of units to buyers in one transaction. MakerBot may have been the first to launch such a system, with their MakerBot Innovation Center a few years ago. When you have, say, 100 units, managing them becomes ridiculous. The reason for this is that most desktop 3D printers have been designed for a single installation with management by a human operator.

ultimaker cura connect to printer

There have been some attempts by other 3D printer manufacturers to move towards efficient methods of managing fleets of 3D printers, which has been very challenging.

#Ultimaker cura connect to printer update#

This is apparently a hardware feature on their equipment, as they also say that they will issue a firmware update on November 7th for Ultimaker 3’s to enable Cura Connect. Note the key phrases: “runs on the Ultimaker 3”, “no server needed” and “all you need is one or more network connected Ultimaker 3”. I am extremely interested to see more about this system, as it may prove a way to dramatically increase the throughput on a set of 3D printers – if they are Ultimaker 3’s. Cura Connect runs on the Ultimaker 3 so there’s no server needed and no complicated setup Intelligent queuing allows you to send multiple print jobs at once and get on with other thingsĮasy to set up. Group 3D printers, then check progress of your prints and maintenance needs, all in one place on your desktop

ultimaker cura connect to printer

Easy queuing and a maintenance schedule make it ideal for maximizing uptime in the office or studio – all you need is one or more network connected Ultimaker 3 and Ultimaker Cura. With Cura Connect, we set out to give users a more efficient way to manage one or multiple 3D printers. what does it do? Here’s all we know, from Ultimaker: They’ve announced something called “Cura Connect”.

#Ultimaker cura connect to printer software#

The other software announcement from Ultimaker is more interesting, and unexpected. At that time we will be able to give it a test and see all the details of the new features. Not quite, it will be available on October 17th.

#Ultimaker cura connect to printer upgrade#

We expected Ultimaker to upgrade Cura to 3.0 eventually, but here it is. I believe this is a very smart move, as users of any 3D CAD software that have enabled the Cura plug-in might be more inclined to purchase Ultimaker 3D printing equipment. The focus for 3.0 seems to be the plugins, as Ultimaker is likely attempting to broaden their ecosystem by involving more parties. Exactly what are the “usual improvements”? Ok, all that sounds good, but it would be terrific if there were more details. Ultimaker Cura 3.0 release comes with the usual improvements and fixes

ultimaker cura connect to printer

Ultimaker-curated plugins create a seamless workflow with other software, including SolidWorks and Siemens NX

ultimaker cura connect to printer

#Ultimaker cura connect to printer plus#

You’ll notice a clearer look and feel, plus choosing your settings is now more intuitive















Ultimaker cura connect to printer